Ammonia, nitrite and pH get all the attention in beginner guides, but water hardness quietly decides whether many fish and invertebrates thrive or struggle. The confusion starts with the fact that “hardness” is actually two separate measurements: GH and KH. They are tested separately, they do different jobs, and you can have high GH with low KH or the reverse. This guide untangles them in plain language.
GH: General Hardness
GH measures dissolved minerals, mainly calcium and magnesium. It is the “hardness” people mean when they call tap water hard or soft. Fish constantly exchange water and salts with their environment through osmoregulation, and each species evolved for a certain mineral level. Livebearers such as guppies and mollies come from hard, mineral-rich water, while most tetras and many South American species come from soft, mineral-poor water.
GH matters most for:
- Shrimp and snails. They need calcium to build shells and to molt. Very soft water causes failed molts in shrimp and eroded, pitted shells in snails.
- Livebearers. Guppies, platies, mollies and swordtails weaken and get disease-prone in very soft water.
- Plants. Calcium and magnesium are plant nutrients, so extremely soft water can cause deficiencies.
GH is measured in degrees (dGH) or ppm, where 1 dGH equals about 17.9 ppm. As a rough scale: 0 to 4 dGH is soft, 4 to 8 is moderately soft, 8 to 12 is moderately hard, and above 12 is hard.
KH: Carbonate Hardness
KH measures carbonates and bicarbonates, and its job is completely different: it buffers pH. Think of KH as a sponge that soaks up the acids your tank constantly produces from fish waste and respiration. While the sponge has capacity, pH stays stable. When KH runs out, there is nothing absorbing acid and pH can fall fast, sometimes crashing a full point or more overnight. Most sudden unexplained pH crashes in mature tanks are really KH problems.
For most community tanks, a KH of 3 to 8 dKH is a comfortable buffer zone. Below 2 dKH, test pH weekly, because the tank has little protection against swings.

How to Test GH and KH
Liquid drop kits are worth the few extra dollars over strips here. With a drop kit you add reagent one drop at a time until the sample changes colour, and the number of drops equals the degrees of hardness, which makes readings precise and the kits last for hundreds of tests. Test your tap water as well as your tank, since tap values are your baseline and can shift seasonally in some areas.
What Your Fish Actually Need
- Livebearers, rainbowfish, African cichlids: GH 10 dGH or higher, KH 5 or higher.
- General community (barbs, danios, rasboras, gouramis): GH 4 to 12, KH 3 to 8. Most farm-bred fish are adaptable across this range.
- Soft-water specialists (wild-type tetras, discus, chocolate gouramis): GH under 6, KH under 4.
- Neocaridina shrimp: GH 6 to 10 with steady KH; stability matters more than the exact number.
The golden rule: a stable, slightly wrong number beats an unstable perfect one. Fish adapt to moderately unsuitable hardness far better than they handle values that bounce around from constant tinkering.
How to Raise GH and KH
- Crushed coral or aragonite in a filter media bag raises both GH and KH slowly and continuously as it dissolves. Start with a small handful per 10 gallons and test weekly.
- Mineral additives such as remineralizing salts made for shrimp keeping raise GH precisely and are dosed per water change.
- Bicarbonate-based buffers raise KH only. Add small amounts, dissolved first, never directly into a stocked tank in one large dose.
How to Lower GH and KH
Lowering hardness is harder than raising it. Chemical “pH down” products do not remove minerals and usually cause swings. The reliable method is dilution: mix your tap water with reverse osmosis (RO) or distilled water until tests hit the target, and use the same ratio at every water change. Driftwood and peat soften water only slightly and unpredictably. If your tap water is very hard and you dream of keeping soft-water species, an RO unit is the honest price of admission; otherwise it is kinder to choose fish that match your tap, such as the livebearers covered in our guppy care and breeding guide.
GH and KH Targets by Species
Most community fish adapt to a wide band, but some groups have real requirements. Use these as working targets, not laws:
| Fish or invertebrate | GH (dGH) | KH (dKH) | Notes |
|---|---|---|---|
| Livebearers (guppies, mollies, platies) | 10–20 | 5–12 | Genuinely need minerals; soft water shortens lifespans |
| Tetras and rasboras | 4–10 | 2–6 | Tank-bred stock tolerates harder water than wild fish |
| Cherry shrimp (Neocaridina) | 6–12 | 2–8 | GH drives molting; sudden swings kill more shrimp than wrong absolute numbers |
| Angelfish and discus | 3–8 | 1–5 | Captive-bred discus no longer need extreme softness |
| Goldfish | 8–20 | 4–10 | Prioritise stable KH; they produce a lot of acidifying waste |
| African rift lake cichlids | 12–25 | 10–18 | The one group where deliberately hardening water is standard |
Test your tap water first, then pick fish that match it. Keeping shrimp or discus in the wrong hardness is possible, but you are working against the water every week.
Common Hardness Mistakes
Chasing exact numbers. A steady GH of 9 beats a GH yo-yoing between 6 and 8. Fish adapt to values; they struggle with movement.
Mixing RO water by feel. If you cut tap water with RO, measure the ratio and keep it identical at every water change. “Roughly half” drifts over months.
Overdosing crushed coral. A small media bag in the filter raises KH slowly and predictably. A thick substrate layer keeps dissolving long after you reach your target.
Confusing units. Liquid kits usually read in dGH/dKH, strips often in ppm. One degree equals 17.9 ppm, and mixing the two up explains most “my hardness is insane” panics. The University of Florida’s water quality notes on alkalinity and hardness cover the underlying chemistry well if you want to go deeper. For the full testing routine, see our water testing guide.
The Bottom Line
Test GH and KH once when you set up a tank and again whenever something seems off. Match fish to your tap water where you can, keep KH above 3 to protect pH, and make any change slowly over days, not hours. Hardness is not a number to chase daily; it is a foundation you set once and check occasionally.
Featured image: ‘Green Gardens’ Sample in Tube (PIA) — Photo: NASA/JPL-Caltech/ASU/MSSS (Public domain), via Wikimedia Commons.